Question 1

What is the difference between A-coded and B-coded M8 connectors, and how do I choose?

Accepted Answer

A-coded M8 connectors are the default choice for many sensor and actuator circuits, while B-coded M8 connectors are used where a different keying pattern is needed for specific signal or communication assignments. The coding prevents incorrect mating between incompatible circuits. Selection should be based on the device port coding, required pinout, and system documentation. Do not select by pole count alone; always match coding, pin assignment, and electrical function to avoid wiring faults.

Question 2

When do I need a shielded M8 double-ended cable for industrial automation?

Accepted Answer

Use shielded M8 cordsets when the signal is sensitive to electromagnetic noise or when cables run near VFD motor lines, contactors, servo power, or high-current conductors. Shielding is especially important for higher-speed communication, encoder feedback, and low-level analog signals. For simple discrete sensors in low-noise environments, unshielded may be acceptable. Ensure shield termination strategy is defined (single-point or multi-point grounding) and consistent with your EMC plan and control cabinet grounding design.

Question 3

What IP rating should I specify for M8 cordsets in wet or dusty environments?

Accepted Answer

For most machine environments with splashing water and dust, IP67 when fully mated is a common baseline. In harsher conditions, including frequent washdown or prolonged moisture exposure, consider IP68-rated variants if supported by the connector design and installation method. Always verify whether the rating applies only in the mated condition and confirm compatible sealing on both connector sides. IP performance also depends on correct torque, clean seals, and avoiding cable jacket damage.

Question 4

How do I select the right M8 cable length without causing voltage drop or signal issues?

Accepted Answer

Start with current draw, supply voltage tolerance at the device, and conductor resistance per meter. Calculate round-trip voltage drop for power pins and check against device minimum voltage requirements. For communication or fast switching signals, consider attenuation, capacitance, and noise pickup as length increases. Choose the shortest practical length that supports routing and service loops, and avoid tightly bundled runs near power cables. For critical links, validate with commissioning measurements under full load.

Question 5

Can I mix M8 and M12 connectors in one machine design?

Accepted Answer

Yes. Many machines use M8 for compact field devices and M12 for higher pin-count, power, or network backbone connections. Keep standards and compatibility clear: M8 interfaces follow IEC 61076-2-104, while many M12 interfaces align with IEC 61076-2-101. Mixing is common, but each interface must match coding, pole count, and pinout at every connection point. Document adapter use carefully and verify IP rating continuity across transitions to avoid weak points in the installation.

Poles	Coding	Protection	LED
4-pole	A	IP65	No
4-pole	A	IP65	No
4-pole	A	IP65	No
4-pole	A	IP65	No
4-pole	A	IP65	No
4-pole	A	IP65	No
4-pole	A	IP65	No
4-pole	A	IP65	No
4-pole	A	IP65	No

Double-Ended Cable - 4

M8 Round Plug Connector M8-M8 Connection Cable Straight/Straight Male/Female 988011

M8 Round Plug Connector M8-M8 Connection Cable Straight/90° Male/Female 988031

M8 Round Plug Connector M8-M12 Connection Cable Straight/90° Without/With LED Male/Female 988291

M8 Round Plug Connector M8-M12 Connection Cable Straight/90° Male/Female 988271

M8 Round Plug Connector M8-M12 Connection Cable Straight/Straight Male/Female 988251

M8 Round Plug Connector M8-M8 Connection Cable Straight Without/With LED Male/Female 988042

M8 Round Plug Connector M8-2m8 Connection Cable Y/Straight Male/Female 987061

M8 Round Plug Connector M8-M8 Connection Cable (Shielded) Straight/Straight Male/Female 988811

M8 Round Plug Connector M8-M8 Connection Cable (Shielded) Straight/90° Male/Female 988831