Question 1

What is the difference between A-coded M12 connectors and other M12 coding types?

Accepted Answer

A-coded M12 connectors are the standard choice for most sensor/actuator and general signal wiring in factory automation. Other coding types (such as B, D, or X coding) are mechanically keyed differently to prevent mismating and are typically used for specific protocols or functions. For open-ended cable selection, always match the coding specified by the device datasheet. Even if thread size is M12, different coding types are not interchangeable.

Question 2

When should I use shielded vs unshielded M12 open-ended cable?

Accepted Answer

Use shielded M12 cable assemblies when routing near variable frequency drives, servo systems, contactors, or long parallel power runs where EMI can affect signal quality. Shielding is especially important for higher-speed or low-level signals and for maintaining stable communication in noisy cabinets. Unshielded cables can be sufficient for short sensor runs in low-noise environments. Follow your grounding concept carefully, typically terminating shield continuity at the appropriate reference point.

Question 3

What IP rating do I need for M12 connectors in industrial automation: IP67, IP68, or higher?

Accepted Answer

IP67 is commonly used for washdown-resistant and dust-tight machine areas where temporary immersion can occur. IP68 or higher may be required for prolonged exposure to water or harsher cleaning processes, depending on site standards. Check whether the rating applies in mated condition, unmated condition with cap, or both. Also verify torque, O-ring condition, and cable entry sealing, since installation quality directly affects real-world ingress protection.

Question 4

How do I select the right cable length for an M12 open-ended cable assembly?

Accepted Answer

Start with routing distance, then add service loop, strain-relief allowance, and motion slack where needed. Avoid excessive extra length, which can increase voltage drop, add noise pickup risk, and complicate cable management. For DC loads, calculate voltage drop using conductor resistance and current over the full loop length. For signal lines, consider capacitance and protocol limits. Standardize practical lengths across machine modules to simplify maintenance and spare parts.

Question 5

Should I choose male or female, and straight or 90° M12 open-ended connectors?

Accepted Answer

Choose male or female based on the mating interface on the field device or panel receptacle; this is defined by the equipment manufacturer and pin/socket safety requirements. Select straight connectors for direct cable exits and open routing space. Choose 90° connectors where depth is limited, side-exit routing is needed, or mechanical stress at the connector must be reduced. Confirm bend radius and clearance to maintain long-term reliability in dynamic installations.

Poles	Coding	Protection	LED
17-pole	A	IP67	No
8-pole	A	IP67	No
8-pole	A	IP67	No
12-pole	A	IP67	No
12-pole	A	IP67	No
12-pole	A	IP67	No
12-pole	A	IP67	No
17-pole	A	IP67	No
17-pole	A	IP67	No
17-pole	A	IP67	No
8-pole	A	IP67	No
8-pole	A	IP67	No
8-pole	A	IP67	No

Open Ended Cable - IP67

M12 Round Plug Connector Open Ended Wire 90° Female 927061

M12 Round Plug Connector Open Ended Wire 90° Male 917021

M12 Round Plug Connector Open Ended Wire Straight Male 917001

M12 Round Plug Connector Open Ended Wire Straight Male 919001

M12 Round Plug Connector Open Ended Wire 90° Female 919061

M12 Round Plug Connector Open Ended Wire Straight Female 919041

M12 Round Plug Connector Open Ended Wire 90° Male 919021

M12 Round Plug Connector Open Ended Wire 90° Male 927021

M12 Round Plug Connector Open Ended Wire Straight Female 927041

M12 Round Plug Connector Open Ended Wire Straight Male 927001

M12 Round Plug Connector Open Ended Wire Straight Female 917041

M12 Round Plug Connector Open Ended Wire 90° Female 917061

M12 Round Plug Connector Open Ended Wire 90° Male 917101