Question 1

What is the difference between M12 A-coded and other M12 coding types for industrial connectors?

Accepted Answer

A-coded M12 connectors are the standard choice for many sensor, actuator, and general-purpose control signals. Other coding types (such as B, D, or X) are mechanically keyed differently to prevent mismating and are typically assigned to specific protocols or applications, including fieldbus or industrial Ethernet variants. If your device port is A-coded, use only A-coded mating connectors. Always verify coding on both the device and cable assembly to avoid mechanical incompatibility and wiring errors.

Question 2

When do I need a shielded M12 cable connector in automation systems?

Accepted Answer

Use shielded M12 cable connectors when cables run near EMI sources such as VFDs, servo drives, motor feeders, contactors, or switching power supplies. Shielding is especially important for low-level analog signals, high-speed data, and long cable runs where induced noise can cause drift, packet errors, or intermittent faults. For best EMC performance, implement proper shield termination and grounding strategy across the full link, not just at one connector, and maintain routing separation from high-current conductors.

Question 3

How do I choose the right IP rating for M12 shielded cable assemblies (IP67 vs IP68)?

Accepted Answer

Select IP rating based on real exposure conditions and whether the connector is mated during operation. IP67 is commonly sufficient for dust-tight performance and temporary immersion protection in many machine environments. IP68 is typically chosen for more demanding or prolonged moisture exposure, depending on manufacturer test conditions. Also check resistance to coolant, oils, and cleaning chemicals, since chemical compatibility can be as critical as ingress protection for connector lifetime.

Question 4

How should I select M12 cable length for sensors and actuators to avoid voltage drop and signal problems?

Accepted Answer

Choose the shortest practical cable length that still supports service loops and machine motion. For power and discrete I/O, calculate voltage drop from current, conductor resistance, and total loop length to ensure device operating voltage remains within tolerance. For analog or communication signals, longer lengths increase susceptibility to noise and attenuation, so shielding quality and routing become more important. Standardize a few validated lengths to simplify spares while avoiding excessive coiled cable in cabinets or on machines.

Question 5

Should I use straight or 90° M12 shielded connectors on machine wiring?

Accepted Answer

Use straight connectors where there is enough axial clearance and minimal risk of cable impact or snagging. Choose 90° versions in tight spaces, near moving assemblies, or where reduced cable protrusion improves protection and bend management. The right-angle option can lower stress at the connector interface when cable routing immediately turns along a panel or device body. Confirm minimum bend radius of the attached cable and ensure orientation supports maintenance access and mating torque application.

Poles	Coding	Protection	LED
3-pole	A	IP67	No
5-pole	A	IP67	No
3-pole	A	IP67	No
3-pole	A	IP67	No
8-pole	A	IP67	No
8-pole	A	IP67	No
5-pole	A	IP67	No
3-pole	A	IP67	No
4-pole	A	IP67	No
4-pole	A	IP67	No
5-pole	A	IP67	No
12-pole	A	IP67	No
8-pole	A	IP67	No
5-pole	A	IP67	No
4-pole	A	IP67	No
4-pole	A	IP67	No

Shielded Cable - IP67

M12 Round Plug Connector Open Ended Wire (Shielded) 90° Female 913241

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Female 913221

M12 Round Plug Connector Open Ended Wire (Shielded) 90° Male 913121

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Male 913061

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Male 917081

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Female 917121

M12 Round Plug Connector Open Ended Wire (Shielded) 90° Female 913281

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Female 913181

M12 Round Plug Connector Open Ended Wire (Shielded) 90° Male 913141

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Male 913081

M12 Round Plug Connector Open Ended Wire (Shielded) 90° Male 913161

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Male 919301

M12 Round Plug Connector Open Ended Wire (Shielded) 90° Female 917141

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Male 913101

M12 Round Plug Connector Open Ended Wire (Shielded) 90° Female 913261

M12 Round Plug Connector Open Ended Wire (Shielded) Straight Female 913201